The part looks great. Everything came as planned. Delivery was on time and install went well.

Thanks, Paragon !

Hard to align with the screen on looks better leaving it off! Looks great and thanks again for the fast response paragon!!!

Looks great and exactly as shown

WOW

Really wanted to enhance the look of the LT6 and give the car a pop of color. Also love how this looks a little old school compared to other engine/manifold covers out there.

I have to say that it exceeded my expectations in terms of how it looks in person! It really sets off the engine bay and is clearly visible through the rear coupe window. I find myself looking back through the rear cabin window at red lights to check out the view as well.

Fairly easy to install and did so by myself. The video walks through the process step by step. It did take a little finagling andmaking sure bolts were too tight before getting the right fit and lined up correctly - but not bad. Install took around 30 minutes with that being said.

Love this high quality aluminum billet cover. The Z06 should come with this from the factory in my opinion. It really makes the engine bay pop. Easy to install. Tighter the small screws last to make things easier.

Outstanding quality and perfect fit! Enhanced the already awesome appearance of the plenums on the 5.5L flat plane beast. Very please with the look!

These manifold covers are awesome looking. I am now ready for a car show. I was not smart enough to get them on so paragon performance put them on. They look great.

Great looking item! But there are a few caveats to it. First, if you have a HTC it is not a simple 5 minute install like they say. You have to partially disassemble the coolant tank and its a much tighter fit in the engine bay. Took me about an hour or so to install it. Second, your engine signature plaque will not be visible anymore as its hidden under the tank. Looks pretty cool when its done though.

Easy install and really looks great! I highly recommend it for those that did not get the painted manifold.

Second set I’ve ordered

Looks great but a little difficult to install. The two large screws would **** in fine without the covers in place, but I had to file a taper onto them to get them started when the covers were in place. It was also a little difficult to get some of the small screws started.

The mesh panel does not have enough width to accommodate the screws.

incrível, simplesmente um novo visual ao meu z06

You have to make sure the center mesh is in the correct place so that the covers will fit

The intake covers are unique among many that are available. They look so much better than other intake covers I have seen installed on other corvettes. I love my Paragon Performance intake covers. The yellow“pops” in my engine bay!

Looks great. Was a little tricky to match the holes for screws.

I'll start by saying that I am very pleased with appearance of the engine cover, once installed. My Z06 came with a black intake manifold, so the engine almost disappeared when looking through the back window. My car is red so I ordered the red cover. The cosmetic improvement is huge, even better than I expected!
However, installation was far from easy.
Assembling the the screen between the two cast aluminum pieces is not nearly as easy is it appears in the video. Having a second person (four hands) would be a plus, even if the supplied screen had not been undersized (mine wasn't wide enough to attach to both sides). Assembling the cover halves on a table with a hole in the bottom would be a plus for underside access, or one could use some tall risers between the table and the covers, tall enough to easily get your your arm underneath.
The video said to re-attach the engine builder plaque using the the supplied 5mm bolts (the instruction sheet says to use the original OEM bolts). Both are too long. They bottom out on the manifold underneath before the plaque is tightened down. I stripped the threads in the thin aluminum engine cover trying to tighten the plaque down using no more force than a nut-driver. So I ended up needing to drill and tap for larger 6mm bolts and also purchase some that were shorter.
I didn't expect to have to file some of the bolt holes in the cover oval to get the attachment bolts to line up with the threaded inserts on the intake manifold. This reminded me of working on my Harley Davidsons, not a Z06. LOL

fits well and well constructed. nice and easy install.

Excellent fitment!!!

It now at a paint shop being painted Rapid Blue to match our 2025 Z06. I'm excited to start dressing up the engine bay of our Z06 coupe.

Fits well and looks great. Very happy with purchase. Top screws on each side are a little hard to **** in. Have to go on a bit of an angle